K-MOULD
Clean the inner cavity and feed port of the K mold before use to prevent impurities from mixing into the molten aluminum and affecting the test results.
Category:
key word:
Service Hotline:+86-18074820425
Consult NowProduct Description
Ⅰ. K-Mould Appearance and Names of Parts
1. Common specifications and models
| K-Mould | Size(mm) | Waffle bars(mm) |
| Standar | 350*72*64 | 40*36*8 |
| Luxury | 487*96*59 | 40*36*8 |
2. Part name

Ⅱ. K-Mould Usage Installation
1. Clean the inner cavity and feed port of the K mold before use to prevent impurities from mixing into the molten aluminum and affecting the test results.
2. Screw the pads into the threaded holes at the bottom of the K mold so that the bottom surface of the K mold and the ground are at an angle of approximately 25°.
PS:
- The gate end is elevated so that the aluminum liquid can quickly flow from the feed port end to the other end under the action of gravity, and then fill the entire K mold cavity to form a complete waffle ingot.
- Elevating the gate end is beneficial to the discharge of air in the inner cavity of the K mold and reduces the air holes in the waffle ingot.
3. Preheat the K mold to 100℃-200℃.
4. Use a clean aluminum liquid spoon to take out a certain amount of liquid aluminum from the furnace and pour it from the gate of the K mold until the aluminum fills the inner cavity and gate of the K mold and the casting is completed.
PS:
- When taking molten aluminum from the furnace, the oxide inclusion layer on the surface should be avoided.
- The casting of each mold must be completed at one time. Multiple castings will increase the risk of bringing in impurities, which will affect the test results.
5. After the aluminum liquid in the K mold is cooled and formed, open the K mold, take out the waffle ingots, close the K mold again, and continue to repeat step 3 for casting. Generally, 4 molds are tested in each batch, and a total of 4 waffle ingots are obtained.
6. Break 4 waffle ingots along the grooves to obtain 20 fractures. Observe the fractures with the naked eye or a low-power microscope, and record the number of impurities.

7. Use the recorded number of impurities to calculate the K value according to the formula. Based on the K value result comparison table, determine the impurity content of the aluminum liquid and make corresponding countermeasures. (For details, see: Chapter 3 K-mode detection method and result evaluation)
Ⅲ. K-Mould Maintenance and Maintenance
1. Daily cleaning: After each use of the K mold, the K mold should be thoroughly cleaned, including removing residues, oil stains, etc. on the surface and inside of the K mold. This helps prevent rust and corrosion of the K mold and maintains the quality of the interior and surface of the K mold.
2. Anti-rust treatment: K mold is prone to rust during storage, so the K mold should be thoroughly dried and sprayed with anti-rust agent before storage. In addition, the storage environment of K mold should be kept dry and ventilated to reduce the risk of rust.
3. Regular maintenance: In addition to daily maintenance, more comprehensive maintenance work should be carried out regularly based on the usage of the K mold. Including disassembly, cleaning, inspection and necessary repair or replacement of K mold.
Related products
A plate-type holding furnace is used for holding the temperature of molten aluminum during metal die casting.
Bath Type Low Pressure Casting Holding Furnace
Bath Type Low Pressure Casting Holding Furnace Equipment Characteristics ◆ The furnace body bears high pressure and high strength. The furnace shell is welded by high strength steel plate. When the test pressure is 0.25 MPa, there is no deformation on the shell. ◆The sealing performance of the furnace body is great. The furnace cover, door and rod connection are reliably sealed with the furnace body, and there is not gas leaks. ◆ No crucible loss. Non-metallic aluminium melt pool, no crucible loss, low use and maintenance costs. ◆ Liquid aluminum does not increase iron. Non-metallic molten pool, aluminum liquid without iron hyperplasia and other pollution. ◆ The melt pool has a long service life. The molten pool is casted with low cement castable for aluminum alloy, which is resistant to aluminum liquid erosion and has a service life of more than 3 years. ◆ Good insulation performance. The lining insulation adopts high-quality insulation materials such as silicon-calcium plate and nano-plate, and the temperature rise of the furnace shell surface is less than 60 °C. ◆ High temperature control precision. With the intelligent temperature control instrument and aluminum temperature thermocouple, the double loop control of aluminum liquid and furnace temperature is realized, and the temperature control accuracy reaches ± 2℃.
Bath Type Melting Furnace Equipment Features ◆ The molten pool is formed by integral injection molding with non-infiltrative and high-strength injection-resistant material (Allied Mineral), and the molten pool does not adhere to aluminum, which slows down the formation of corundum tumor. ◆ Non-metallic molten pool, liquid aluminum without iron hyperplasia and other pollution. ◆ The melt hearth service live is more than 3 years. ◆ The furnace village adopts multi-layer anti-leakage technology, without the consideration of aluminum liquid ' string leakage ' lining. ◆ The furnace cover has a cylinder rotating lift, which is convenient for molten pool cleaning, slag removal operation, furnace cover and electric heating element maintenance. ◆ It has a variety of safety protection such as aluminum liquid over-temperature alarm and furnace over-temperature alarm.
Count Pressure Casting Holding Furnace
Count Pressure Casting Holding Furnace The electrical type counter pressure furnace is made of high-quality electrical resistance wire as heating element. The furnace lining is composed of fiber module and fiber blanket, which has less heat storage and good heat preservation performance. The crucible furnace is suitable for graphite crucible. The crucible has good high temperature oxidation resistance and can be used for melt insulation before differential pressure casting. The crucible furnace is equipped with a power plug, which can be conveniently, safely and reliably connected with the power socket on the counter pressure casting machine.
MESSAGE
We will contact you within one working day. Please pay attention to your email.